JMT 30.5×30.5mm Dual Gyro F7 F4 Flight Controller AIO OSD 5V 8V BEC & Black Box for RC Drone FPV Racing Quadcopter Accessories Fashion
Description
Item Name:Â Dual Gyro F7 Flight Controller AIO OSD BEC
Optional Version: Acro(Standard) Version ( Without Barometer & Blackbox & MPU6000)
               Deluxe Version ( With Barometer & Blackbox)
Input Voltage: 2-6S Lipo
      ACRO(Standard) Version Don t support MPU6000
BEC 1 :Â 5V 2A ( for LED, Buzzer, Receiver etc.)Â Â
BEC 2: 8V 3AÂ ( for Camera, VTX, open close it by USER2)Â
UART Series: 6 UARTSÂ ( UART1-UART6)Â
Support Dual Camera Input ( C1, C2 for Video Input;Â C1 in default, can switch by USER1)
Package Included:
1x F7 Flight Controller Board
4x M3 Anti-vibration Standoff
It adopts STM32F405 high-performance processor and MPU6000 gyroscope accelerometer, integrated adjustable OSD, built-in 5V 2A (internal power supply, receiver, LED, BUZZER, etc.), 8V 3A BEC (camera and picture transmission) The two independent BECs work separately, do not interfere with each other, optimize the circuit design, and high-performance hardware to further ensure the powerful performance of the flight control. Convenient interface definitions, leaving the available interfaces. In addition, 8P and 6P 1.0MM sockets are designed to facilitate direct input of the plug wire. Reserve black box TF deck, support up to 32G card, record flight data with 16kHz recording rate.
technical parameter:
Model: JMT F4
Main control chip: STM32F405RGT6
Gyro: MPU6000
Barometer: None (reserved pad)
OSD chip: AT7456E
Black Box: TF deck
LED programming: support
BB ring: support
Input voltage: 2-6S
I2C interface: support
BEC-1: 5V 2A (internal power supply, receiver, LED, BUZZER, etc.)
BEC-2: 8V 3A (camera and picture transmission power supply)
Serial control port: three channels (UART1, UART3, UART6)
Flight Control Firmware: Betaflight
Hole position and damping ball hole position conversion: 30.5*30.5mm, φ4mm
Flight control size: 36*36mm
Weight: 6.9g
packing list:
F4 Flight Control X 1
M3 blue shock absorber ball X 4
Interface description:
GND: Ground
+5V: BEC 5V 2A cont. MAX.2.5A
3.3V: LDO3.3V, MAX.300MA
VBAT+: share Lipo power
CUR: ESC Current signal input
S1, S2, S3, S4, S5, S6: ESC Signal
VTX: Video output for video Transmitter
VIN: Camera Video input
8V: Current 3A, video Transmitter and Camera Power supply
BZ-:General active 5V buzzer for dbuz 5V
RSSI: Receiver RSSI INPUT
LED: WS2812 LED signal
SCL & SDA: I2C_SCL & I2C_SDA
PPM: PPM RC Receiver Input
SBUS: SBUS RC Receiver Input
D I: DSM and IBUS RC Receiver Input
(RC Receiver, SBUS, IBUS, DSM: RX1)
T1: UART1 TX1
R3 & T3: UART3 RX3 and TX3
R6 & T6: UART6 RX6 and TX6
Â
Â
Â
Item Name:Â Dual Gyro F7 Flight Controller AIO OSD BEC
Optional Version: Acro(Standard) Version ( Without Barometer & Blackbox & MPU6000)
               Deluxe Version ( With Barometer & Blackbox)
Input Voltage: 2-6S Lipo
      ACRO(Standard) Version Don t support MPU6000
BEC 1 :Â 5V 2A ( for LED, Buzzer, Receiver etc.)Â Â
BEC 2: 8V 3AÂ ( for Camera, VTX, open close it by USER2)Â
UART Series: 6 UARTSÂ ( UART1-UART6)Â
Support Dual Camera Input ( C1, C2 for Video Input;Â C1 in default, can switch by USER1)
Package Included:
1x F7 Flight Controller Board
4x M3 Anti-vibration Standoff